A/C AC Compressor w/Clutch For 2009 2010-2012 2013 2014 2015 Toyota Camry 2.5L

A/C AC Compressor w/Clutch For 2009 2010-2012 2013 2014 2015 Toyota Camry 2.5LA/C AC Compressor w/Clutch For 2009 2010-2012 2013 2014 2015 Toyota Camry 2.5LNOTE:NOTE:Each AC air compressor comes with about 100ML of Oil.

You dont need to add oil additionally. Each AC air compressor comes with about 100ML of Oil.

You dont need to add oil additionally. This compressor comes pre-filled with the correct amount of oil.

Thus, there is no need to add any additional oil to your system. This compressor comes pre-filled with the correct amount of oil.

Thus, there is no need to add any additional oil to your system. Please add refrigerant to 70-80% without filling up. Please add refrigerant to 70-80% without filling up. There may be noise if the refrigerant is added too muchThere may be noise if the refrigerant is added too muchFitment:Fitment:2012-2015 Toyota Camry 2.5L2012-2015 Toyota Camry 2.5L2009-2012 Toyota RAV4 2.5L2009-2012 Toyota RAV4 2.5LInterchange Part Number:Interchange Part Number:CO 11303C,6512815,883100R014,2022690,157367,158367,TEM255740,TEM275768,255740,275768,4711018,140761NIP,639891CO 11303C,6512815,883100R014,2022690,157367,158367,TEM255740,TEM275768,255740,275768,4711018,140761NIP,639891Installation MethodInstallation MethodAttention Please:Attention Please:Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken. Be sure to clean the air conditioning system before installation, otherwise it will cause compression broken.1.

Remove compressor:1.

Remove compressor:Remove the A/C belt from the A/C compressor pulley.

May involve loosening the belt Voltager (if equipped). Remove the A/C belt from the A/C compressor pulley.

May involve loosening the belt Voltager (if equipped).2.receiver drier or accumulator, orifice tube or expansion valve.2.receiver drier or accumulator, orifice tube or expansion valve.3. Disconnect the negative battery cable.3. Disconnect the negative battery cable.4. Remove the bolt that secures refrigerant lines to the A/C compressor.

Inspect A/C lines for any contamination such as metal or excessive dirt inside of them.

If you find any4. Remove the bolt that secures refrigerant lines to the A/C compressor.

Inspect A/C lines for any contamination such as metal or excessive dirt inside of them.

If you find anycontamination the system will need to be cleaned. Flush the condenser and evaporator using NON-OIL BASED A/C flush.

On expansion valve systems.

The valve must be removed beforecontamination the system will need to be cleaned. Flush the condenser and evaporator using NON-OIL BASED A/C flush.

On expansion valve systems.

The valve must be removed beforethe evaporator can be flushed.

Flushed condensers from outlet to inlet and evaporators from inlet to outlet.the evaporator can be flushed.

Flushed condensers from outlet to inlet and evaporators from inlet to outlet.5. Drain all the oil from the new compressor ,if you compressor has a drain plug you will need to open it up and drain what oil is in there too.5. Drain all the oil from the new compressor ,if you compressor has a drain plug you will need to open it up and drain what oil is in there too.6. Install half oil charge into the compressor and the remainder throughout the system.

Turn compressor shaft 8-10 full revolutions to insure front seal and other internal6. Install half oil charge into the compressor and the remainder throughout the system.

Turn compressor shaft 8-10 full revolutions to insure front seal and other internalparts are lubricated.parts are lubricated.7. Install new receiver drier or accumulator and new orifice tube or expansion valve.7. Install new receiver drier or accumulator and new orifice tube or expansion valve.8. Evacuate the A/C system for a minimum of one hour.8. Evacuate the A/C system for a minimum of one hour.9. After evacuation install half the refrigerant charge and let the system set for 1 minute.

This will allow the refrigerant to pick up oil and spread more evenly throughout9. After evacuation install half the refrigerant charge and let the system set for 1 minute.

This will allow the refrigerant to pick up oil and spread more evenly throughoutthe system.the system.10. Turn on the A/C system with the engine running and check to see if cold air is now coming out of the air duct.10. Turn on the A/C system with the engine running and check to see if cold air is now coming out of the air duct.11. If the A/C system is functioning ,you may find that your electric radiator fan and compressor clutch will be cycling off and on depending on the outside air temperature.11. If the A/C system is functioning ,you may find that your electric radiator fan and compressor clutch will be cycling off and on depending on the outside air temperature. To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table. To confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table.